The LEDs on this assembly can be connected and powered in series or singly for full control of each LED making the SR-08-WC310 ideally suited for:
- Flashlights
- Bicycle Lights
- Diving Lights
- Color Tuned Lighting
|
- Lightsabers
- Spot lighting
- Task Lamps
- Fiber Optic Illuminators
|
Need four different color LEDs mounted to this base? We offer a customizable version here.
Specifications
| LED Color |
Cool White |
| Lumens @ 350mA |
540 lm |
| Lumens @ 700mA |
940 lm |
| Lumens @ 1000mA |
1280 lm |
| Efficacy @ 350mA |
133 Lm/W (From datasheet) |
| Efficacy @ 700mA |
116 Lm/W (From datasheet) |
| Typical Color Temperature (1,2) |
5650K |
| Color Temperature Range (1) |
4500 to 10000K |
| Color Rendering Index (1) |
70 CRI |
| Beam Angle (3) |
120° |
| Recommended Operating Current (4) |
700 mA |
| Maximum Rated Drive Current |
1000 mA |
| Typical Forward Voltage (5) |
11.6 Vf |
| Maximum Forward Voltage (5,7) |
13 Vf |
| Thermal Resistance (1,6) |
7.5 C°/W |
| Max Recommended Junction Temp |
150 °C |
| Operating Temperature Range |
-40 to 135 °C |
| Dimensions L x W x H |
23 x 23 x 5 mm |
|
|
- Values based on 350mA and a Thermal Pad temperature of 25 °C.
- Note that while the typical color temperature for this LED is shown as 5650K, LEDs with temperatures lower than 6000K are rarely available. The more common bins have color temperatures of 6000K or higher
- Viewing angle is the off axis angle from lamp centerline where the luminous intensity is ½ of the peak value.
- This is the maximum operating current that we recommend for this LED. Higher drive currents may be possible, but will require careful design of a suitable cooling system.
- At the recommended operating current.
- Typical thermal resistance from the LED Junction to the bottom of the FR4 board.
- This is the value we recommend you use for determining driver input voltage.
* Results will vary depending on the quality of the dielectric material used in the MCPCB base.
Download Center
Additional Information
The SR-08-WC310 can be ordered in any quantity with quantity discounts available.
If you order more than one piece of this part, pieces may be shipped as part of a v-scored panel.
Important Note About Stock: We usually only keep a small number of this part in stock. However, we can produce virtually any quantity that you may require on demand. Please contact us for lead times for orders above 1,000 pieces.
 Do you need LEDs with a specific flux, color or forward voltage? Order this part in 1,000 piece increments and we will build it using LEDs from the same bin. We can also provide specific bin numbers. Contact us for availability.
Click here to learn more about LED binning.
Thermal Management
SR-08-WC310 LED assemblies must be operated to ensure that the junction temperature of the LEDs are kept well below the maximum ratings as specified in the LXML-PWC2 datasheet. A heat sink must always be used when operating this assembly. The size of the heat sink will depend on the ambient temperature and the current that is used to power the LEDs. Bench testing that we have conducted with a SR-08-WN300 assembly powered at 700mA in an open air environment and an ambient temperature of 25°C has indicated that a heat sink with a thermal rating of 8 C°/W or lower should be adequate. However, you will need to perform your own testing and analysis to determine if this size of heat sink will be suitable for your application.
The SR-08-WC310 must be fastened to the heat sink using a thermal interface material such as our pre-cut Bond-Ply 100 pressure sensitive, double sided thermal tape or Arctic Silver thermal adhesive. Before fastening the assembly to the heat sink, ensure that the two mating surfaces are perfectly flat and clean in order to maximize heat transfer to the the sink. Be careful not to warp or distort the PC Board by over tightening the screws.
Connection Diagrams
|
