Free Shipping Offer Details On orders over $200 to the USA and Canada.
Click for details.

Cyan 505nm Rebel LEDs on a SABER 2 Series Connected Tri-Star Base - 228 lm @ 350mA

Cyan 505nm Rebel LEDs on a SABER 2 Series Connected Tri-Star Base - 228 lm @ 350mA
The SW-13-C2 LED module features three series connected LXML-PE01-0070 cyan, Rebel LEDs soldered to a SABER 20mm Tri-Star base.

Using proven MCPCB technology, SABER tri-star LED modules offer a cost-effective, reliable solution for R&D, MROs, OEMs, and Makers/Artists. Wiring connections are made using standard bench top tools and hand soldering techniques.

The SW-13-C2 footprint is one of the most commonly used Tri-LED form factors and is compatible with a full selection of compatible optics.
Part Number : SW-13-C3
Quantity Price
10 - 24 $16.18
25 - 49 $15.33
50 - 99 $14.48
100 - 249 $13.62
250 - 999 $12.77
1000+ $11.92
Quantity discount pricing will be automatically
applied when you add this part to the cart.
Quantity
Select the LEDs To Be Mounted
Cyan LED (LXML-PE01-0070)
SW-13 (SW-13b)
Product Attributes
LED ColorCyan
(1)Lumens @ 350mA228 lm
(2)Wavelength Range490 to 515nm
(3)Beam Angle125°
(4)Recommended Operating Current350 mA
Maximum Rated Drive Current1000 mA
(1,5)Typical Forward Voltage8.7 Vf
(1,5,7)Maximum Forward Voltage10.53 Vf
(6)Thermal Resistance10 C°/W
Max Recommended Junction Temp150 °C
Operating Temperature Range-40 to 135 °C
Dimensions L x W x H20 x 20 x 3.7 mm
  1. LEDs connected in series.
  2. Values based on 350mA and a Thermal Pad temperature of 25 °C.
  3. Viewing angle is the off axis angle from lamp centerline where the luminous intensity is ½ of the peak value.
  4. This is the maximum operating current that we recommend for this LED module. Higher drive currents may be possible, but will require careful design of a suitable cooling system.
  5. At the recommended operating current.
  6. Typical thermal resistance from the LED Junction to the bottom of the LED module.
  7. This is the value we recommend you use for determining driver input voltage.
  8. This information is for reference only. Refer to the manufacturers datasheet for official specifications.
Documents & Media
DatasheetsSP-03 Module Datasheet
LXML-PE01-0070 Rebel LED Datasheet
CAD & DrawingsSP-03 Module Dimensional Drawing
SP-03 Module STEP 3D Model File
SP-03 Module IGES 3D Model File
Lumileds Supporting DocumentsLUXEON Rebel Thermal Measurement Guidelines
Photobiological Safety Report (Eye Safety)

Thermal Management

The SABER SP-03 Tri-Star module requires careful attention to mounting and cooling to ensure that the junction temperature of the LED is kept well below the maximum rating as specified in the LED documentation published by Lumileds.

For optimal cooling, we recommend that the module be mounted to a suitable finned heat sink (aluminum or copper) that is exposed to open air. The module can be mounted to the heat sink in one of two ways:

Before fastening the module to the heat sink, ensure that the two mating surfaces are perfectly flat and clean in order to maximize heat transfer to the the sink.

Mechanical fasteners are not recommended for this module.

The bottom of the LED module is electrically neutral, so it is not necessary to electrically isolate the base from the cooling surface.

Optic Compatibility

The SABER SP-03 Tri-Star LED module is compatible with the following optics:

Color Mixing

Looking for a color mixing Tri-Star LED module? Our SW-03 LED module can be ordered with any color combination of Rebel LEDs mounted to a SABER tri-star base. LEDs are powered separately, giving you full independent control of each LED.

Additional Information

The SW-13-C2 can be ordered in any quantity with quantity discounts available.

If you order more than one piece of this part, pieces may be shipped as part of a v-scored panel.

Important Note About Stock: We usually only keep a small number of this part in stock. However, we can produce virtually any quantity that you may require on demand. Please contact us for lead times for orders above 1,000 pieces.

Binned LEDsDo you need LEDs with a specific flux, color or forward voltage? Order this part in 1,000 piece increments and we will supply it using LEDs from the same bin. We can also provide specific bin numbers. We can also provide specific bin numbers. Contact us for availability.

Click here to learn more about LED binning.

Support
LED Knowledgebase
[email protected]
Phone: 1-347-223-5077
Fax: 1-403-775-4020
Legal & Business Information
Compliance Documents
Privacy Policy
Terms and Conditions
Returns & Refund Policy
Shipping Policy
Payment Options
About Us
Product Index
Category Index
We Accept
Visa Mastercard American Express Pay with Paypal Bitcoin Wire Transfers Check Terms
 
 
Currency conversion software
Copyright Quadica Developments Inc. All Rights Reserved. eCommerce Software by 3dcart.