Free Shipping Offer Details On orders over $200 to the USA and Canada.
Click for details.

Cyan (505nm) Rebel LED on a SinkPAD-II 40mm Round 7-Up Base - 532 lm @350ma

Cyan (505nm) Rebel LED on a SinkPAD-II 40mm Round 7-Up Base - 532 lm @350ma
The SP-02-C2 LED module features 7 LXML-PE01-0070 Cyan, Rebel LEDs and NTC thermistor soldered to a SinkPAD-II 40mm Round base.

The SinkPAD-II uses second generation technology to minimize thermal resistance by eliminating the dielectric layer so that the LED thermal pad is soldered directly to the aluminium base. This ensures the lowest possible LED junction temperature, resulting in increased LED life, light power output and overall reliability.
Part Number : SP-02-C2
Quantity Price
10 - 24 $60.33
25 - 49 $57.16
50 - 99 $53.98
100 - 249 $50.81
250 - 999 $47.63
1000+ $44.46
Quantity discount pricing will be automatically
applied when you add this part to the cart.
Quantity
Product Attributes
LED ColorCyan
(1)Lumens @ 350mA532 lm
(2)Wavelength Range490 to 515nm
(3)Beam Angle125°
(4)Recommended Operating Current350 mA
Maximum Rated Drive Current1000 mA
(1,5)Typical Forward Voltage20.3 Vf
(1,5,7)Maximum Forward Voltage24.57 Vf
(6)Thermal Resistance10.7 C°/W
Max Recommended Junction Temp150 °C
Operating Temperature Range-40 to 135 °C
Dimensions L x W x H40 x 40 x 3.7 mm
  1. LEDs connected in series.
  2. Values based on 350mA and a Thermal Pad temperature of 25 °C.
  3. Viewing angle is the off axis angle from lamp centerline where the luminous intensity is ½ of the peak value.
  4. This is the maximum operating current that we recommend for this LED module. Higher drive currents may be possible, but will require careful design of a suitable cooling system.
  5. At the recommended operating current.
  6. Typical thermal resistance from the LED Junction to the bottom of the module.
  7. This is the value we recommend you use for determining driver input voltage.
  8. This information is for reference only. Refer to the manufacturers datasheet for official specifications.
Documents & Media
DatasheetsSP-02 Module Datasheet
LXML-PE01-0070 Rebel LED Datasheet
Thermistor Curves
SP-02 Thermal Monitoring Guidelines
CAD & DrawingsSP-02 Module Dimensional Drawing
SP-02 Module STEP 3D Model File
SP-02 Module IGES 3D Model File
Lumileds Supporting DocumentsLUXEON Rebel Thermal Measurement Guidelines
Photobiological Safety Report (Eye Safety)

Thermal Management

A Vishay NTC 10K Thermistor (NTHS0805N02N1002J) is mounted to the board to monitor temperature and can be used for foldback temperature control. For more information about using the thermistor, please review our SP-02 Onboard Thermistor Temperature Measurement application note.

SP-02-C2 LED modules must be operated to ensure that the junction temperature of the LEDs are kept well below the maximum ratings as specified in the LXML-PE01-0070 datasheet. A suitable finned heat sink or other cooling method must always be used when operating this module. The size of the heat sink will depend on the ambient temperature and the current that is used to power the LEDs. Bench testing that we have conducted with a SP-02-C2 module powered at 700mA in an open air environment and an ambient temperature of 25°C has indicated that a heat sink with a thermal rating of 9 C°/W or lower should be adequate. However, you will need to perform your own testing and analysis to determine if this size of heat sink will be suitable for your application.

The SP-02-C2 must be fastened to the heat sink using a thermal interface material such as our pre-cut Bond-Ply 100 pressure sensitive, double sided thermal tape or Arctic Silver thermal adhesive. Before fastening the module to the heat sink, ensure that the two mating surfaces are perfectly flat and clean in order to maximize heat transfer to the the sink.

Mechanical fasteners are not recommended for this module.

The bottom of the module is electrically neutral, so it is not necessary to electrically isolate the base from the cooling surface.

Optic Compatibility

The SP-02-C2 has been specifically designed to accommodate the Polymer and Khatod 7 Cell Cluster series of optics, including:

Drive Requirements

This LED module can be powered in parallel or in series with the addition of 0 ohm resistors or solder dots.

Want to power this module from a voltage as low as 10VDC? Then check out the FlexBlock LED driver. A single driver can power all 7 of these LEDs connected in series with any voltage from 10V to 18V*.

* The maximum input voltage to the driver must be less than the total forward voltage of all series connected LEDs.

Connection

Additional Information

Need a mixture of different color LEDs mounted to this board? A color mixing version of this LED module is available.

The SP-02-C2 can be ordered in any quantity with quantity discounts available.

If you order more than one piece of this part, pieces may be shipped as part of a v-scored panel.

Important Note About Stock: We usually only keep a small number of this part in stock. However, we can produce virtually any quantity that you may require on demand. Please contact us for lead times for orders above 1,000 pieces.

Binned LEDsDo you need LED modules with a specific flux, color or forward voltage? Order this part in 1,000 piece increments and we will supply it using LEDs from the same bin. We can also provide specific bin numbers. Contact us for availability.

Click here to learn more about LED binning.

Support
LED Knowledgebase
[email protected]
Phone: 1-347-223-5077
Fax: 1-403-775-4020
Legal & Business Information
Compliance Documents
Privacy Policy
Terms and Conditions
Returns & Refund Policy
Shipping Policy
Payment Options
About Us
Product Index
Category Index
We Accept
Visa Mastercard American Express Pay with Paypal Bitcoin Wire Transfers Check Terms
   
Currency conversion software

Copyright Quadica Developments Inc. All Rights Reserved.
QUADICA® is a registered trademark of Quadica Developments Inc.
Commerce Software by 3dcart.