Your Choice Of Any 7 Rebel LEDs Soldered To A SinkPAD-II 40mm Round Base
The high power LED module features 7 high brightness Rebel LED soldered to a SinkPAD-II™ 40mm round base. Each LED on this module is individually powered and controlled.
SinkPAD-II™ technology minimizes thermal resistance by eliminating the dielectric layer so that the LED thermal pad is soldered directly to the aluminum base. This ensures the lowest possible LED junction temperature, resulting in increased LED life, light power output, and overall reliability.
Series connected & color mixing versions of this LED module are available.
Discount Pricing
| Quantity | Discout |
|---|---|
| 10-24 | 5% |
| 25-49 | 10% |
| 50-99 | 15% |
| 100-249 | 20% |
| 250-999 | 25% |
| 1000+ | 30% |
Important Notes About Ordering The SP-02 Color Mixer
- Orders for color mixers cannot be canceled or altered once your order has been reviewed and submitted to production! So be very sure that you have selected the correct LEDs before you submit your order!
- Before you order cyan LEDs, please be sure to read this important information about color variations.
- Modules are designed to power each LED separately for controlled color mixing. However, you can easily convert the module to power all seven LEDs in series with two solder dots. See the connection diagrams below.
Thermal Management
A suitable finned heatsink or other cooling method must always be used with the SP-02 LED module to ensure that the junction temperature of the LEDs is kept well below the maximum rating specified in the Lumileds datasheet. The size of the heatsink will depend on the ambient temperature and the current used to power the LEDs.
Bench testing that we have conducted with SP-02 modules powered at 700mA in an open-air environment and an ambient temperature of 25°C has indicated that a heat sink with a thermal rating of 9 C°/W or lower should be adequate. However, you must perform your own testing and analysis to determine if the heatsink you select is suitable for your application.
We recommend that the module be mounted to an aluminum or copper finned heatsink exposed to open air for optimal cooling. The module can be mounted to the heat sink in one of two ways:
- 40mm round pressure-sensitive, thermally conductive tape (Recommended)
- Arctic Silver thermally conductive adhesive
Before fastening the module to the heat sink, ensure that the two mating surfaces are perfectly flat and clean to maximize heat transfer to the heatsink. Mechanical fasteners are not recommended for this module.
A Vishay NTC 10K Thermistor (NTHS0805N02N1002J Thermistor datasheet) is mounted to the board to monitor temperature and can be used for foldback temperature control. For more information about using the thermistor, please review our SP-02 Onboard thermistor temperature measurement information in the SP-02 module datasheet.
The bottom of the LED module is electrically neutral, so it is unnecessary to electrically isolate the base from the cooling surface.
Connection
This LED module can be powered in parallel or series by adding 0-ohm resistors or solder dots.
Want to power this module from a voltage as low as 10VDC? Then check out the FlexBlock LED drivers. A single driver can power all 7 of these LEDs connected in series with any input voltage from 10V to 18V. Note that the maximum input voltage to the driver must be less than the total forward voltage of all series-connected LEDs.
LED Binning
Order quantities less than 250 pieces are produced from unbinned stock (cut strips). We can supply binned LED modules (built from full reels)) If you order in 250+ quantities, please contact us for binning details.
Learn more about LED binning here.
A current-regulating LED driver is required between the power supply and the LED module to ensure that the LED is not powered above its maximum current rating. You can learn more about powering high-power LED modules here.
All drivers listed here are 100% compatible with the SP-02 LED module. The driver you select will depend on your specific requirements.
High-power LEDs include a primary optic for protection and light optimization. However, a secondary optic is often essential for better focus and light distribution.
All the optics listed here are 100% compatible with the SP-02 LED module.
To maximize life and reliability, a heatsink or alternate method of cooling is required to ensure that the junction temperature of the LED is kept well below its maximum temperature rating.
Refer to our Thermal Management articles for assistance selecting an appropriate heatsink from the available options here.
| RoHS Status | RoHS 3 Compliant |
| REACH Status | REACH Uneffected |
| Conflict Minerals Report | CMRT Rev 6.22 |
| Proposition 65 Statement | Proposition 65 |
| PFAS Declaration | PFAS Declaration |
| ECCN | EAR99 |
| HTS | 8543.70.71.00 |
| Country of Origin | CA |
Important Notes About Ordering The SP-02 Color Mixer
- Orders for color mixers cannot be canceled or altered once your order has been reviewed and submitted to production! So be very sure that you have selected the correct LEDs before you submit your order!
- Before you order cyan LEDs, please be sure to read this important information about color variations.
- Modules are designed to power each LED separately for controlled color mixing. However, you can easily convert the module to power all seven LEDs in series with two solder dots. See the connection diagrams below.
Thermal Management
A suitable finned heatsink or other cooling method must always be used with the SP-02 LED module to ensure that the junction temperature of the LEDs is kept well below the maximum rating specified in the Lumileds datasheet. The size of the heatsink will depend on the ambient temperature and the current used to power the LEDs.
Bench testing that we have conducted with SP-02 modules powered at 700mA in an open-air environment and an ambient temperature of 25°C has indicated that a heat sink with a thermal rating of 9 C°/W or lower should be adequate. However, you must perform your own testing and analysis to determine if the heatsink you select is suitable for your application.
We recommend that the module be mounted to an aluminum or copper finned heatsink exposed to open air for optimal cooling. The module can be mounted to the heat sink in one of two ways:
- 40mm round pressure-sensitive, thermally conductive tape (Recommended)
- Arctic Silver thermally conductive adhesive
Before fastening the module to the heat sink, ensure that the two mating surfaces are perfectly flat and clean to maximize heat transfer to the heatsink. Mechanical fasteners are not recommended for this module.
A Vishay NTC 10K Thermistor (NTHS0805N02N1002J Thermistor datasheet) is mounted to the board to monitor temperature and can be used for foldback temperature control. For more information about using the thermistor, please review our SP-02 Onboard thermistor temperature measurement information in the SP-02 module datasheet.
The bottom of the LED module is electrically neutral, so it is unnecessary to electrically isolate the base from the cooling surface.
Connection
This LED module can be powered in parallel or series by adding 0-ohm resistors or solder dots.
Want to power this module from a voltage as low as 10VDC? Then check out the FlexBlock LED drivers. A single driver can power all 7 of these LEDs connected in series with any input voltage from 10V to 18V. Note that the maximum input voltage to the driver must be less than the total forward voltage of all series-connected LEDs.
LED Binning
Order quantities less than 250 pieces are produced from unbinned stock (cut strips). We can supply binned LED modules (built from full reels)) If you order in 250+ quantities, please contact us for binning details.
Learn more about LED binning here.
| Operating Temperature Range | to °C |
| Refer to the product datasheets for complete specifications. | |
|---|---|
A current-regulating LED driver is required between the power supply and the LED module to ensure that the LED is not powered above its maximum current rating. You can learn more about powering high-power LED modules here.
All drivers listed here are 100% compatible with the SP-02 LED module. The driver you select will depend on your specific requirements.
High-power LEDs include a primary optic for protection and light optimization. However, a secondary optic is often essential for better focus and light distribution.
All the optics listed here are 100% compatible with the SP-02 LED module.
To maximize life and reliability, a heatsink or alternate method of cooling is required to ensure that the junction temperature of the LED is kept well below its maximum temperature rating.
Refer to our Thermal Management articles for assistance selecting an appropriate heatsink from the available options here.
| RoHS Status | RoHS 3 Compliant |
| REACH Status | REACH Uneffected |
| Conflict Minerals Report | CMRT Rev 6.22 |
| Proposition 65 Statement | Proposition 65 |
| PFAS Declaration | PFAS Declaration |
| ECCN | EAR99 |
| HTS | 8543.70.71.00 |
| Country of Origin | CA |
Documents
| Datasheets | Module Datasheet LED Datasheet |
| CAD & Drawings | Module Dimensional Drawing Module STEP 3D Model Module IGES 3D Model |
| Lumileds Supporting Documents | LUXEON Rebel Thermal Measurement Guidelines Photobiological Safety Report (Eye Safety) |
Compliance
| RoHS Status | RoHS 3 Compliant |
| REACH Status | REACH Uneffected |
| Conflict Minerals Report | CMRT Rev 6.22 |
| Proposition 65 Statement | Proposition 65 |
| PFAS Declaration | PFAS Declaration |
| ECCN | EAR99 |
| HTS | 8543.70.71.00 |
| Country of Origin | CA |
