Free Shipping Offer Details On orders over $200 to the USA and Canada.
Click for details.

ANSI White (3045K) LUXEON Rebel ES LED on a SinkPAD-II 40mm Round 7-Up Base - 1015 lm @ 700mA

ANSI White (3045K) LUXEON Rebel ES LED on a SinkPAD-II 40mm Round 7-Up Base - 1015 lm @ 700mA
The SP-02-X9 has been discontinued. Our SP-02-T3 may be a suitable replacement.
Additional non-stocked ANSI White SinkPAD-II round 7-Up assemblies can be ordered here.

The SP-02-X9 has been specifically designed to accommodate the Polymer and Khatod 7 Cell Cluster series of optics, including:

The LEDs can be powered singly or in series with the addition of 0 ohm resistors or solder dots. A Vishay NTC 10K Thermistor (NTHS0805N02N1002J) is mounted to the board to monitor temperature and can be used for foldback temperature control. For more information about using the thermistor, please review our SP-02 Onboard Thermistor Temperature Measurement application note.

Want to power this LED module from a voltage as low as 10VDC? Then check out the FlexBlock LED driver. A single driver can power all 7 of these LEDs connected in series with any voltage from 10V to 18V*.

Need a mixture of different color LEDs mounted to this board? A custom version of this module is also available.

* The maximum input voltage to the driver must be less than the total forward voltage of all series connected LEDs.

LED Color ANSI White
Lumens @ 350mA 567 lm
Lumens @ 700mA 1015 lm
Lumens @ 1000mA 1379 lm
Efficacy @ 350mA 84 Lm/W (Calculated)
Efficacy @ 700mA 69 Lm/W (Calculated)
Typical Color Temperature (1) 3045K
Color Temperature Range (1) 2870 to 3220K
Color Rendering Index (1) 95 CRI
Beam Angle (2) 120°
Recommended Operating Current (3) 700 mA
Maximum Rated Drive Current 1000 mA
Typical Forward Voltage (4) 20.3 Vf
Maximum Forward Voltage (4,6) 22.75 Vf
Thermal Resistance (1,5) 6.7 C°/W
Max Recommended Junction Temp 150 °C
Operating Temperature Range -40 to 135 °C
Dimensions L x W x H 40 x 40 x 3.7 mm
  1. Values based on 350mA and a Thermal Pad temperature of 25C.
  2. Viewing angle is the off axis angle from lamp centerline where the luminous intensity is ½ of the peak value.
  3. This is the maximum operating current that we recommend for this LED. Higher drive currents may be possible, but will require careful design of a suitable cooling system.
  4. At the recommended operating current.
  5. Typical thermal resistance from the LED Junction to the bottom of the board.
  6. This is the value we recommend you use for determining driver input voltage.
Download Center
SP-02 Datasheet Thermistor Curves SP-02 Dimensional Drawing
LXW9-PW30 Datasheet SP-02 Thermal Monitoring Guidelines SP-02 IGES 3D Model File
SP-02 STEP 3D Model File
Additional Ordering Information

The SP-02-X9 can be ordered in any quantity with quantity discounts available.

If you order more than one piece of this part, pieces may be shipped as part of a routed panel with v-scored tabs for separating the parts from the panel.

Important Note About Stock: We usually only keep a small number of this part in stock. However, we can produce virtually any quantity that you may require on demand. Please contact us for lead times for orders above 300 pieces.

Binned LEDsDo you need LEDs with a specific flux, color or forward voltage? Order this part in 300 piece increments and we will 0build it using LEDs from the same bin. We can also provide specific bin numbers. Contact us for availability.

Click here to learn more about LED binning.

Thermal Management

SP-02-X9 LED assemblies must be operated to ensure that the junction temperature of the LEDs are kept well below the maximum ratings as specified in the LXW9-PW30 datasheet. A heat sink must always be used when operating this module. The size of the heat sink will depend on the ambient temperature and the current that is used to power the LEDs. Bench testing that we have conducted with a SP-02-N4 module powered at 700mA in an open air environment and an ambient temperature of 25°C has indicated that a heat sink with a thermal rating of 9 C°/W or lower should be adequate. However, you will need to perform your own testing and analysis to determine if this size of heat sink will be suitable for your application.

The SP-02-X9 must be fastened to the heat sink using a thermal interface material such as our pre-cut Bond-Ply 100 pressure sensitive, double sided thermal tape, Arctic Silver thermal adhesive or screws with thermal grease. Before fastening the module to the heat sink, ensure that the two mating surfaces are perfectly flat and clean in order to maximize heat transfer to the the sink. If you are using screws, be careful not to warp or distort the module by over tightening the screws.

Connection Diagrams
SR-02 Series Operation
SR-02 Single Operation
SR-02 Thermistor Connection
LED Knowledgebase
Phone: 1-347-223-5077
Fax: 1-403-775-4020
Legal & Business Information
Privacy Policy
Terms and Conditions
Returns & Refund Policy
Shipping Policy
Payment Options
About Us
Product Index
Category Index
We Accept
Visa Mastercard American Express Pay with Paypal Bitcoin Wire Transfers Check Terms

Currency conversion software
Copyright Quadica™ Developments Inc. All Rights Reserved. eCommerce Software by 3dcart.